Charging at high and low temperatures (BU14) Rechargeable batteries operate under a reasonably wide temperature range. This, however, does not automatically permit charging under these same temperature extremes. While operating batteries under hot or cold conditions cannot always be avoided, the user has some control over charging. Efforts must be made to charge the batteries at moderate temperatures. Nickel-cadmium: In general, older battery technologies are more tolerant to charging at temperature extremes. Nickel-cadmium can be fast-charged in an hour or so, however, such a charge should only be applied within temperatures of 5°C and 45°C (41°F and 113°F). More moderate temperatures of 10°C to 25°C (50°F to 77°F) produce better results. Charging below 5°C requires a reduce charge rate of 0.1C (one tenth of the rated current). This is in line with the rate at which the oxygen and hydrogen can be absorbed within the cell. Because of the decreased combination rate at low temperatures, too rapid a charge would cause excessive cell pressure, which would lead to cell venting. Such a battery would never reach full charge state under these conditions. Industrial batteries that need to be fast-charged at low temperatures include a thermal blanket to maintain the battery at an acceptable temperature. Once a charging temperature is enabled, the very process of gas recombination, which occurs during charge, also generates some heat to assist the cold temperature charging. The ideal charger would adjust itself to obtain equilibrium between gas recombination and charge current. Nickel-metal-hydride is less forgiving than the nickel-cadmium if charged under high and low temperatures. Nickel-metal-hydride cannot be fast charged below 10°C (45°F), neither can it be slow charged below 0°C (32°F). Some industrial chargers are designed to adjust the charge rate to existing temperatures. Price sensitivity does not permit elaborate temperature sensing on consumer chargers. At higher temperatures, the charge acceptance of nickel-based batteries is drastically reduced. A battery that provides a capacity of 100% when charged at moderate room temperature can only accept 70% if charged at 45°C (113°F), and 45% if charged at 60°C (140°F). This demonstrates the poor summer performance of some vehicular chargers. Lithium- ion offers good charging performance at cold and hot temperatures. The acceptable charge range is 0° to 45°C (32°F to 113°F). It is recommended, however, to reduce the charge rate to less than 1C at temperatures of 5°C to 0°C (41°F to 32°F). It is important to know that consumer grade lithium-ion batteries cannot be charged below 0°C (32°F). Although the packs appear to be charging normally at freezing temperatures, the cell impedance goes up and the acceptance of the ions on the anode is drastically reduced. What is most troubling is the plating of metallic lithium that occurs on the anode. The higher the charge rate, the more pronounced the plating will be. A prolonged charge at cold temperatures will eventually compromise the safety of the pack. The plating is permanent and no amount of cycling can reverse this effect. Unknown to the user, such a battery will become more vulnerable to failure if subjected to impact, crush or high rate charging. Venting with flame could be the result. Quality chargers reduce the charge current at cold temperatures and avert a charge altogether below 0°C (32°F). When charging a cold battery, allow the pack to warm up before putting it into the charger. Discharging a lithium-ion battery at cold temperature does not cause any harm. The lower performance will only be noticeable while the pack is dwelling in the cold state. There are specialty Li-ion batteries that allow low-temperature charging. These packs are made for military and aerospace applications. The lower viscosity of the electrolyte of these batteries may reduce the rate capability and decrease the cycle life. Beside lower performance, the high purchase price is another concern for the consumer. There are also safety concerns when using lithium-ion at high temperatures, especially in cells containing cobalt and/or nickel electrodes. Raising the temperature of a fully charged cell, or applying an overcharge, could cause a spontaneous thermal runaway. The higher the state-of-charge, the less heat is required to induce a thermal runaway. Manganese based cells [spinel] are thermally more stable and the thermal stability is the same whether fully charged or overcharged. Lead-acid is reasonably forgiving on temperature extremes, as we are familiar with our car batteries. Part of this tolerance is credited to the sluggishness of the lead-acid system. Some battery brands permit freezing and low level charging; others sustain damage and deliver reduced capacity and a short service life. To improve charge performance of lead-acid batteries at colder temperatures and avoid thermal runaway during heat spells, controlling the voltage limits, to which the battery is charged, is important. Implementing such a measure can prolong battery life by up to 15%. General guidelines suggest a compensation of approximately 3mV per cell per degree Celsius. The voltage adjustment has a negative coefficient, meaning that the voltage threshold drops as the temperature increases. Heat kills batteries. The warmer the cells, the shorter the life is. Elevated temperatures cannot always be prevented, especially during fast charging, but efforts must be made to keep this time brief. While 45°C (113°F) is acceptable if kept short, at 50°C (122°F) and above, the battery starts to suffer. Note that the cells inside the pack are always a few degrees warmer than the temperature of the housing. Ultra-fast chargers Some charger manufacturers claim amazingly short charge times of 30 minutes or less. With well-balanced cells and operating at moderate room temperatures, nickel-cadmium batteries designed for fast charging can indeed be charged in a very short time. This is done by simply dumping in a high charge current during the first 70% of the charge cycle. In the second phase of the charge cycle, the charge current must be lowered. The efficiency to absorb charge is progressively reduced as the battery moves to a higher state-of-charge. If the charge current remains too high in the later part of the charge cycle, the excess energy turns into heat and high cell pressure. Eventually, venting will occur, releasing oxygen and hydrogen. Not only do the escaping gases deplete the electrolyte, they are highly flammable! A white powdery substance accumulating at the vent area indicates previous venting. Ultra-fast charging can only be applied to batteries that are designed for fast charging. Applying a high current charge to regular cells will cause the conductive path to heat up. The contacts on portable packs also suffer if the current handling of the spring-loaded plunger contacts is underrated. These contacts may wear out prematurely. Often, a fine and almost invisible crater appears on the tip of the contact, which causes a high resistive path or forms an isolator. The heat generated by a bad contact often melts the plastic. Higher contact tensions improve the current flow. Aged batteries with high internal resistance and mismatched cells do not lend themselves to ultra-fast charging, even if they are designed for it. Low cell conductivity turns into heat, which further deteriorates the cells. The weak cells holding less capacity are fully charged before the others and begin to heat up rapidly. Some batteries create sufficient heat to soften and distort the plastic housing. Temperature sensing is a prerequisite with fast and ultra-fast charging. Several manufacturers offer pulse chargers. Interspersing brief discharge pulses between each charge pulse can further enhance charging. This method promotes recombination of oxygen and hydrogen gases, resulting in reduced pressure buildup and lower cell temperature. Pulse chargers are also known to reduce crystalline formation (memory) on nickel-based batteries. Most Cadex chargers for nickel-based batteries apply this feature. Some advanced chargers regulate the charge current according to the battery's ability to accept charge. An empty battery will initially take a very high charge current. Towards the end of a charge, the current is tapered down. Aged batteries are given their due respect and are automatically charged at rates suitable to their condition. _________________________ Created: June 2003, Last edited: February 2006 About the Author Isidor Buchmann is the founder and CEO of Cadex Electronics Inc., in Vancouver BC. Mr. Buchmann has a background in radio communications and has studied the behavior of rechargeable batteries in practical, everyday applications for two decades. Award winning author of many articles and books on batteries, Mr. Buchmann has delivered technical papers around the world. Cadex Electronics is a manufacturer of advanced battery chargers, battery analyzers and PC software. For product information please visit www.cadex.com.
| ||||||
|
Learning
the basics about batteries - sponsored by Cadex Electronics Inc.
| ||||||